在线中文字幕免费观看视频,亚洲男同性恋18,18在线观看视频免费

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

雕刻機使用前后需要做哪些工作？

來源：http://dzxiaoche.com 時間：2021-01-07

雕刻機的操作是有學問的，簡單的啟動開機大家都會，那只不過是動動手指的事情，但是您一定不知道在您按下按鈕的那一刻起整部機器經過了哪些運作，不如讓我們不做一個詳細的了解，對您機器的保養和壽命都是有好處的。

The operation of engraving machine is learned. We all know how to start it. It's just a matter of moving your fingers. But you don't know what operation the whole machine has gone through when you press the button. It's better for us not to do a detailed understanding, which is good for the maintenance and life of your machine.

一、電腦方面

1、 Computer

定期查殺病毒，但注意工作時不可以打開防毒程度，小心干擾。定期清理機箱灰塵，注意機箱的散熱，小心灰塵過多引起工控卡出錯。定期整理磁盤碎片，優化電腦系統。

Check and kill the virus regularly, but pay attention not to open the anti-virus level when working, and be careful of interference. Clean up the dust of the chassis regularly, pay attention to the heat dissipation of the chassis, and be careful of the industrial control card error caused by too much dust. Regularly defragment the disk and optimize the computer system.

五軸保麗龍雕刻機

Five axis styrofoam engraving machine

二、清理

2、 Clean up

定期清理工控箱，灰塵時電路板的殺手。定期清理絲杠，防止絲杠上粘有異物，絲杠在設備中很重要，他決定了機器的精度，而且絲杠在傳動過程中也起重要作用。

Regularly clean the industrial control box, dust is the biggest killer of circuit board. Regularly clean the lead screw to prevent foreign matters sticking on the lead screw. The lead screw is very important in the equipment, which determines the accuracy of the machine, and the lead screw also plays an important role in the transmission process.

工作完了應及時清理臺面，這就給木工雕刻機下次工作提供了方便。清理導軌及導軌旁邊的材料屑，以防止因碎屑干擾導致機器在工作過程中出現卡機。

After the work, the table should be cleaned in time, which provides convenience for the next work of woodworking carving machine. Clean the guide rail and the material scraps beside the guide rail to prevent the machine from jamming during operation due to the interference of scraps.

三、上油

3、 Oiling

加完油后慢速來回走動，保證潤滑油能夠均勻加到導軌與絲杠上。機器若長期不用，應定期加油空走，以保證傳動系統的靈活性。

After adding oil, walk back and forth slowly to ensure that the lubricating oil can be evenly added to the guide rail and lead screw. If the machine is not used for a long time, it should be refueled regularly to ensure the flexibility of the transmission system.

清理干凈導軌與絲杠，可用布不脫毛把導軌和絲杠上的油污和材料屑清理掉。因氣溫較低，可把導軌和絲杠都加機油，加防凍機油。加油周期為每月兩次，也就是每兩周加一次油。

First of all, clean the guide rail and lead screw, and use cloth to clean the oil and material debris on the guide rail and lead screw. Due to the low temperature, the guide rail and lead screw can be added with engine oil and antifreeze engine oil. The refueling cycle is twice a month, that is, once every two weeks.

四、溫度

4、 Temperature

機器不用時，若室溫較低更好倒出水箱里的水，防止凍裂水箱與水管。保證操作間環境溫度，木工雕刻機達到室溫，少工作人員也不會很冷。查看所加油標準適用溫度，少達到低溫度。

When the machine is not in use, if the room temperature is low, it is better to pour out the water in the water tank to prevent the water tank and water pipe from cracking. Ensure that the operating room temperature, wood engraving machine to room temperature, at least the staff will not be very cold. Check the applicable temperature of the refueling standard, and at least reach the low temperature.

溫度對于木工雕刻機的影響不是很大，但由于用戶給絲杠加黃油，冬季也忘了清理，導致每次開機運行不開，有的工作室氣溫很低，雖然加了機油，可還是凍上了，機器運行不起來。

The influence of temperature on woodworking engraving machine is not very big, but because the user adds butter to the screw and forgets to clean it in winter, the machine can't run every time. The temperature of some workrooms is very low. Although the engine oil is added, it is still frozen and the machine can't run.

五、冷卻水

5、 Cooling water

有條件可以使用防凍液冷卻。注意環境溫度，小心因水溫過冷而造成水箱與水管凍裂。冷卻水為主軸電機正常工作的必要條件，若冷卻水過臟會對電機造成嚴重傷害，保證冷卻水的清潔及水泵的正常工作。注意水位，絕不可使水冷主軸電機出現缺水現象，使電機熱量不能及時導出。

If possible, antifreeze can be used for cooling. Pay attention to the ambient temperature, be careful of the water tank and water pipe crack caused by the water temperature is too cold. Cooling water is a necessary condition for the normal operation of the spindle motor. If the cooling water is too dirty, it will cause serious damage to the motor, so as to ensure the cleaning of the cooling water and the normal operation of the water pump. Pay attention to the water level, never make the water-cooled spindle motor lack of water, so that the motor heat can not be exported in time.